|
本帖最后由 choi 于 5-26-2022 15:13 编辑
There is no need to read the rest of any document quoted below.
(1)
(a) How Do BB Guns Work? HowStuffWorks, updated Feb 21, 2021
https://entertainment.howstuffworks.com/question649.htm
consecutive paragraphs:
"To understand how BB guns work, let's first look at conventional guns. The basic idea behind almost any firearm, from a pistol to a cannon, is to create a small explosion just behind a projectile positioned in a cylinder. When the explosion tries to expand in a gun, it is very limited as to where it can go: The edges of the cylinder are stronger than the force of expansion, so it can't expand out in every direction. The only way it can expand is down the cylinder, the barrel of the gun. If a projectile (a bullet, for example) is in the way, the expanding matter from the explosion will push the projectile forward as it makes its way down the barrel.
"The principle behind BB guns is pretty much the same as in firearms, except there is no explosion. The expanding matter is ordinary air, carbon dioxide or some other gas. Before you fire the gun, the gas is compressed so that it has a greater density, and consequently a greater pressure than the air in the atmosphere outside the gun. The compressed gas is stored in an airtight container until you pull the trigger. This opens up the gas container so the gas can flow out into the barrel, just behind the BB. Since it is more compressed, the gas behind the BB pushes out with greater force than the air in the atmosphere pushes in, and the BB is propelled forward at great speed. This is the idea behind all gas-powered guns, including high-powered air rifles and paintball markers.
"There are several different air-gun designs, which differ mainly in the source of the compressed air:
"• In pneumatic designs, you build up a reservoir of compressed gas by manually pumping air. The movable lever on the bottom of the gun moves a small piston in a tube. Inside the tube, there is a check valve that lets air flow in but not back out. In this way, each pump of the gun increases the amount of air in the reservoir, which has a set volume. Since mass is increased while volume is held constant, the density and pressure of the air increases with every pump.
"• Another common system is the spring air design. In this sort of gun, the 'pump' lever pushes back on a small piston, which compresses a spring behind it. As the piston slides back, it catches on a small, spring-driven latch that swivels on a tiny pin. This latch, commonly called a sear, holds the piston in position, so the spring stays compressed. When you pull the trigger, it pushes on the sear so it lifts off the piston. With the piston unlatched, the spring can expand out, pushing the piston forward. This quickly compresses the air in the chamber behind the BB, building up the pressure needed to propel it down the barrel.
(B) BB gun
https://en.wikipedia.org/wiki/BB_gun
("For airguns firing non-spherical pellets, see Pellet gun. For airguns firing 6 mm plastic [spherical] projectiles, see Airsoft gun. A BB gun is a type of air gun designed to shoot metallic spherical projectiles called BBs (not to be confused with similar-looking bearing balls)"/ section 1 History: explaining the term BB)
section 2 Operation:
"BB guns can use any of the operating mechanisms used for air guns. However, due to the inherent limited accuracy and short effective range of the projectile, only the simpler and less expensive mechanisms are generally used for guns designed to fire only BBs.[citation needed]
"Because the strength of the steel BB does not allow it to be swaged with the low propelling force used to accelerate it through the barrel, BBs are slightly smaller (4.3 to 4.4 mm (0.171 to 0.173 in)) than the internal diameter of the barrel (4.5 mm (0.177 in)). This limits accuracy because little spin is imparted on the BB. It also limits range, because some of the pressurized gas used to accelerate the BB leaks around it and reduces the overall efficiency. Since a BB will easily roll unhindered down the barrel, it is common to find guns that use a magnet in the loading mechanism to hold the BB at the rear of the barrel until it is fired.[citation needed]
"The traditional and still most common powerplant for BB guns is the spring-piston pump, usually patterned after a lever-action rifle or a pump-action shotgun. The lever-action rifle was the first type of BB gun, and still dominates the inexpensive youth BB gun market.
(C) Spring air or spring piston design is Just spring. A few pictures suffice.
• Load Break Barrel Air Rifles Safely. Hard Air Magazine (HAM; 'The best airgun test reviews and news'), July 3, 2014.
https://hardairmagazine.com/buye ... -air-rifles-safely/
("Break barrel air rifles are the most common type of airgun")
ATACHMENT 1
• Jim Carmichael, The Often Underrated Compressed Air Gun. Mother Earth News, undated.
https://www.motherearthnews.com/ ... r-gun-zmaz81mjzraw/
ATTACHMENT 2
In the left lower corner, a gun has its (single) break barrel cocked. (the other two guns presumably cock by different methods). At the top of this illustration, both a pellet and a spring are displayed and marked.
• Dr Amitabha Mukherjee, The Bravo Present --> the Air Gun. In Hands on Lab (July-November 1999): ME371 Project. Department of Mechanical Engineering, IIT Kanpur (IIT = Indian Institute of Technology).
https://www.cse.iitk.ac.in/users ... 1/brijes/index.html
ATTACGNENT 3
In the illustration, break barrel is red, whose cocking results in compressed spring via a cyan lever.
|
|